Have you had enough of your shower curtain? Perhaps you thought of having a shower enclosure and learning how to install shower glass doors so your bathroom will look as stylish and attractive as the trendy home décor magazines.
You’ve come to the right place if you want to learn how to install shower glass doors. We’ll help you accomplish your vision by providing you with a guide on how to install glass shower doors.
Types of Shower Doors to Consider When You Want to Install Shower Glass Doors or Replace the Glass of Shower Door:
- Steam Door
- Framed Shower Glass Doors
- Pivot Shower Door
- Frameless Shower Doors
- Sliding Shower Doors
- Neo-Angle Door
- Curved Shower Door
- Hinged Shower Door
- Bi-Fold Shower Doors
High-Quality Shower Glass Options to Consider When You Want to Install Shower Glass Doors:
- Rain Glass
- Clean Shower Glass DoorsTinted Glass
- Frosted Glass
- Clear Tempered Glass Doors
Necessary Tools and Materials to Install Shower Glass Doors
- Hacksaw
- Materials
- A glass shower set with a suitable kit
- Caulking gun
- Measuring tape
- Fills
- Silicone
- Drilling bits
- Screws
- Electric screwdriver
- Pencil
- Screwdriver
- Hammer
- Hole saw
- Sand cloth
- Level
- Electric drill
- Scissors
- Slip joint pliers
We highly recommend you read the best guide for installing shower enclosures before going further.
How to Install Shower Glass Doors
Now let’s get to the steps for installing shower glass doors.
Step 1: Necessary Measurements to Install Shower Glass Doors
Determine the door’s position before you begin to install shower glass doors for your shower enclosure. Then, using a measuring tape, you should measure the width and height of the walls.
Don’t be concerned if the wall is not the same width from top to bottom. To properly install shower glass doors, it will be sufficient to measure the width multiple times to identify the narrowest point.
Step 2: The Process to Install Shower Glass Doors
Begin to install shower glass doors by attaching the two rails to the horizontal walls of your bathroom well over the shower tub. For the very first part of the job, use tape. Then accurately measure the distance between those two rails and, if needed, modify the bottom one.
Please remember that not all walls are even, so you may need to trim and adapt. If you need to cut the rail, use a hacksaw, but move the rubber inside to keep it safe.
The rough edges should then be filed smooth and soft. Depending on the material, use a traditional file or suitable sandpaper.
Step 3: Fit In the Bottom Rail
Place the bottom rail between the two wall rails to properly install shower glass doors. Check the manual to see which parts will fit the others because it’s critical not to deform the rails accidentally.
The next step to install shower glass doors is to tighten the sidewall rails with tape. This will allow you to move all of the tracks slightly to make any necessary adjustments. It is usually a good idea to place the bottom rail in the center of the bath curb or step wall of your shower. Use a level to ensure that all rails are level.
Step 4: Drill the Holes
Mark the holes where you intend to drill into the wall before removing the tape from the wall tracks. The manufacturer has already prepared the holes in the rails. Remove the rails and begin drilling. Because each glass shower is unique, there are no hard and fast rules for how to install shower glass doors.
Depending on the quality of your wall, anchors may be required, especially if it is unstable or empty.
Step 5: Fixate the Bottom Rail
Apply silicone caulking to the bottom rail with a caulk gun so that it can be attached to the bath curb.
For the next step in installing shower glass doors, place the bottom rail between the two wall rails and press it firmly against the floor. If excess caulking comes from underneath, wipe it away to ensure a clean surface.
Step 6: Measure and Cut the Upper Rail
Measure the horizontal rails at the top. If necessary, shorten the higher track.
Make sure to cut 1/6 of an inch (4 mm) shorter so you can install shower glass doors without force. After cutting, use the file to smooth out the outside and inside edges. That way, you’ll have no trouble fitting them quickly.
Step 7: Fixate the Upper Rail
The next step to install shower glass doors is to slide the higher track down onto the two horizontal rails on the wall. It should be a perfect fit. Start drilling from the inside and outside of both rails with a drill.
You can then connect them one to the other. This should be done on both rails. Always use stainless screws to install shower glass doors so you can prevent hardware rusting from high moisture existing in the shower.
Step 8: Put and Adjust Rollers
The rollers are typically found on sliding doors. Please place them in the appropriate position on the door.
Often, it would help if you changed the door’s height while installing shower glass doors, depending on the position of the roller. Install the rollers on both doors according to the manufacturer’s instructions. Make any necessary adjustments.
Step 9: Install the Handle
Depending on the door type, you can choose from various handle shapes. Choose the ones you like best and install them.
Step 10: Hang the Door
To be done with installing shower glass doors, gently hang the door from the upper rail, taking care to set the rollers into the grooves. When they click on it, you’ll know everything is in place, and you’ve done with the.
Conclusion
The last step to install shower glass doors is for you to wait for 24 to 48 hours to let the silicone dry completely. Then test the shower glass doors for leaking. One other thing you need to remember is that clean shower glass doors after taking shower to maintain its beauty.
